View FLC43XWC8V-02_6929473.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

to : specification of fujitsu tft-lcd module FLC43XWC8V-02 approval this product is designed, developed and manufactured as contemplated for general use, including without limitation, general office use, personal use, household use, and ordinary industrial use, but is not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury, severe physical damage or other loss (hereinafter ?high safety required use?), including without limitation, nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system. if customer?s product possibly falls under the category of high safety required use, please consult with our sales representatives in charge before such use. in addition, fdtc shall not be liable against the customer and/or any third party for any claims or damages arising in connection with the high safety required use of the product without permission . specification no. : tech bes lcd-00149 issue date : dec. 5, 2002 issued by : f. yamada director products engineering dept. lcd products div. fujitsu display technologies corporation date by
? 2 FLC43XWC8V-02 3 1 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation revision history revision date prepared checked approved summary 01a jul. 12, 2002 h. takahashi f. yamada 1st issue 02b oct. 11, 2002 s. sekido f. ya m a d a change gasket location and constant number of fuse 03b oct. 25, 2002 k. yonemura f. ya m a d a change gasket location (3 locations) 04b nov. 12, 2002 s. sekido f. ya m a d a change gasket location (2 locations) 20020712 takahashi yamada 34 02 20020807 takahashi yamada revise p4,6,8,12-13,15,17,32-33 add p14 03 20020924 takahashi yamada revise p3,8,20,21 04 20021205 sekido takahashi yamada revise p2, 6, 7, 8, 16, 21 and add p22
? 2 FLC43XWC8V-02 3 2 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation table of contents 1. applications ............................................................................................................ 3 2. product name and model name 2-1.product name ........................................................................................................... 3 2-2.model name .............................................................................................................. 3 3. overview.................................................................................................................... 3 4. configuration........................................................................................................ 3 5. mechanical specifications............................................................................. 4 6. absolute maximum ratings............................................................................. 5 7. recommended operating conditions ....................................................... 5 8. electrical specifications .............................................................................. 6 9. optical specifications ...................................................................................... 8 10.interface specifications 10-1.signal descriptions ................................................................................................. 12 10-2.color data assignment .......................................................................................... 15 10-3.input signal timing ............................................................................................... 16 10-4.correspondence between data and display position .......................................... 18 10-5.power supply sequence ......................................................................................... 18 11.backlight specifications 11-1.pin configuration for backlight ............................................................................ 19 11-2.ccfl ...................................................................................................................... . 19 11-3.life...................................................................................................................... ..... 19 11-4.lamp assembly set (for replacement) ................................................................. 19 12.appearance specifications 12-1.zone ...................................................................................................................... ... 20 12-2.bright spot.............................................................................................................. 2 0 12-3.test condition......................................................................................................... 20 12-4.standard ................................................................................................................. 2 0 13.environmental specifications .................................................................. 23 14.indications............................................................................................................. 24 15.packaging ............................................................................................................... 24 16.warranty................................................................................................................. 29 17.precautions .......................................................................................................... 29 18.precautions for use......................................................................................... 32 19.miscellaneous..................................................................................................... 32 04 20021205 total revision
? 2 FLC43XWC8V-02 3 3 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 1. applications 1. applications 1. applications 1. applications this specification is applied to the 17.0 in. xga-wide supported tft-lcd module. 2. 2. 2. 2. product name product name product name product name and model name and model name and model name and model name 2-1. product name : lcd module 2-2. model name : FLC43XWC8V-02 3. overview 3. overview 3. overview 3. overview this lcd module has a tft active matrix type liquid crystal panel 1280768 pixels, and diagonal size of 43cm (17.0-inch). this module supports 1280768 xga-wide mode (non-interlace). this lcd has a xga-wide-capable 1ch-lvds interface and can display 16 million colors. by timing control signal, images are displayed on the screen at given value under specified timing. control signals to this lcd module are enab (data enable signal), dclk signal and rgb data signal. data signal is transmitted with single port. (8 bit for each r, g, b) the power supply of this lcd module is +5v dc. this module has the characteristics that apply to tco?99. ? 4. configuration 4. configuration 4. configuration 4. configuration this lcd module consists of a color tft-lcd panel that mounted with tft driver ics, a cold-cathode fluorescent tube back-light, a lvds interface pcb, a structure and a bezel. and these components are integrated in a lcd module. cold-cathode fluorescent tube and lamp holder are replaceable. fig.4-1 shows a block diagram of this lcd module. 03 20020924 add ?t (application of tco?99)
? 2 FLC43XWC8V-02 3 4 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation figure 4-1. block diagram 5. mechanical specifications 5. mechanical specifications 5. mechanical specifications 5. mechanical specifications table 5-1 shows the mechanical specifications of this lcd module. table 5-1. mechanical specifications item specifications unit remark dimensions 413.8263.518.4(typ.) mm display resolution (12803) 768 ? display dot area 369.6221.76 mm dot pitch (0.096253) 0.28875 mm edge type backlight is used. ( 2.6 ccfl4) outward appearance is shown at page 32 and 33. aspect ratio 1 ? : ? 1 ? weight 2,000 max g fg-sg short circuit ? back light (ccfl) (separate) interface circuit dc/dc converter data driver panel 1 280 3(rgb) 768 inverter gate driver input signal rxclk ? rxclk+ rx0 ? rx0+ rx1 ? rx1+ rx2 ? rx2+ rx3 ? rx3+ power supply dc bias power supply c ir cu i t 02 20020807 change page no. of outline drawing
? 2 FLC43XWC8V-02 3 5 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 6. absolu 6. absolu 6. absolu 6. absolute maximum ratings te maximum ratings te maximum ratings te maximum ratings table 6-1 shows the absolute maximum rating of this lcd module. table 6-1. absolute maximum ratings item symbol min. typ. max. unit supply voltage v cc 0.3 ? 6.0 v input voltage v in 0.3 ? vcc+0.3 v 7. recommended operating cond 7. recommended operating cond 7. recommended operating cond 7. recommended operating conditions itions itions itions table 7-1 shows the recommended operating conditions of this lcd module. table 7-1. recommended operating conditions item symbol min. typ. max. unit supply voltage v cc 4.75 5.0 5.25 v ripple voltage (vcc) v rp ? ? 100 mvp-p
? 2 FLC43XWC8V-02 3 6 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 8. electrical specifications 8. electrical specifications 8. electrical specifications 8. electrical specifications table 8-1 shows the electrical specifications of this lcd module. table 8-1. electrical specifications item symbol condition min. typ. max. unit remark supply current i cc ? (600) 680 (1000) 900 ma *1 ?h? level logic input voltage v ih v cc= +5.00.25v vss=0v dclk=32.498mhz 0.7 vcc ? v cc+ 0.3 v *2 ?l? level logic input voltage v il gnd ? 0.3 vcc v *2 =50khz, ta=25oc ? 1230 1600 ccfl turn on voltage v s =50khz, ta=0oc ? ? 1600 vrms lighting voltage v l =50khz =10.5ma 590 630 670 vrms *4 back light lighting frequency l =580 vrms 630 40 50 60 khz *3 tube current l =50khz v =580 vrms 630 9.5 10.5 11.0 arms *4 (*1) typical current value is measured when gray scale (vertical 256 levels) is displayed at vcc=5.0v. maximum current value is measured when stripes with respect to each rgb dot are displayed at vcc=5.0v. without rush current. (*2) timing control circuit input voltage (*3) backlight specifications are valid when using a suitable inverter such as the ?flcv-15? of fdtc. (*4) tube current (i l ) shows the value of the current and voltage that is consumed at one lamp. (4 tubes/unit) this lcd module has 4 lamps. each 2 lamps are placed at upper and lower side of the display. 2 lamps are connected in parallel. each low voltage terminals (gnd side) are bound into 1 line cable. (see 11-1. pin configuration for backlight) 02 20020807 correct backlight spec. 04 20021205 change the values of ?u parts
? 2 FLC43XWC8V-02 3 7 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation note 1) measurement circuit based on fig.8-1. fig.8-1. measurement circuit note 2) equivalent circuit based on fig.8-2 (a), (b). fig.8-2 (a) equivalent circuit of logic signal input fuse: kab2402 252 na29010(matsuo electric co., ltd.)or equivalent. ? emi filter: sgm20c1e332-2a(sumitomo metal)or equivalent. ? fig.8-2 (b) equivalent circuit of power supply fuse (2.5a) ? gnd v cc fg frame ground emi filter internal circuit 10 ? +5v gnd ? a c gnd icc ? l ? !? module vcc ? v l ? c l ? v s ? dc/dc converter back- light input signals(lvds-1ch) ?
? ?
?? ?? ??? ??? ???? ?? ??? ?? ??? + =j internal circuit differential input 100 ? 2 FLC43XWC8V-02 3 8 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 9. optical specifications 9. optical specifications 9. optical specifications 9. optical specifications table 9-1 shows the optical specifications of this lcd module. table 9-1. optical specifications ta=25o c specifications remark item symbol condition min. typ. max unit note horizontal l,r u,d =0o 85 ? ? deg visual angle vertical u,d cr 10 l,r =0o 85 ? ? deg (1)(2) (3)(5) (6) contrast ratio cr l,r,u,d =0o 210 350 ? 600 ? ? white/ black (1)(2) (3)(5) ta=25oc ? 15 30 ms response time(on) (b w) t on l,r, u,d =0o ta=0oc ? 50 100 ms ta=25oc ? 10 25 ms response time(off) (w b) t off l,r, u,d =0o ta=0oc ? 50 100 ms (1) (4) (5) brightness i 400 350 ? 500 450 ? ? cd/m 2 (1)(5) brightness uniformity ? i 70 75 ? ? ? % (1)(5) (7) x 0.283 0.313 0.343 ? chromaticity w y l,r,u,d =0o v cc =5v, i l =10.5ma (at maximum brightness) 0.299 0.329 0.359 ? white *1 r red 0.65, 0.34 typ. g green 0.30, 0.59 typ. b (x, y) blue 0.15, 0.14 typ. (1) (5) -curve 2.4 typ. lcd panel type tft color display mode normally black va wide viewing angle technology mva-premium optimum viewing angle ? (symmetry) (6) display color 16 million (each 6-bit+2-bit frc) color of non-display area black surface treatment anti-glare (haze value:25%, 3h(at weight of 300g)) (*1) specified value is measured in 20~30 minutes after lighting on (lcd module single). a required value may not be achieved on condition that lcd module is built in the cabinet because of its radiation. (note1) cs-1000 (minolta co., ltd.) , bm-5a(topcon) or equivalent luminance colorimeter should be used for the measurement. field=2o, l=500mm the specified value of viewing angle, contrast, brightness, brightness uniformity and chromaticity are under the dark room condition (1lux or less). ?s min.value of contrast ratio 02 20020807 add ? 2 FLC43XWC8V-02 3 9 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation note 1) definition of viewing angle (1) based on fig.9-2. * u =0o, d =0o, l =0o, r =0o fig.9-2. definition of viewing angle (1) note 2) definition of viewing angle (2) based on fig.9-3. fig.9-3. definition of viewing angle (2) note 3) definition of contrast ratio (cr) determined by formula (1) based on fig.9-4.voltage-brightness characteristics. l w (brightness at white) = -------- (1) l b (brightness at black) 0 fig.9-4. voltage-brightness characteristics *0o ( front ) u ??? y + top (12 o?clock direction) lcd module x ? left (9 o?clock direction) y ? bottom (6 o?clock direction) x + right (3 o?clock direction) d l r display surface display surface max typ min l,r,u,d =0o panel drive voltage [v] brightness | l white l 0 black l ,
? 2 FLC43XWC8V-02 3 10 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation note 4) definition of response time based on fig.9-5. on off 100% 0% fig.9-5. definition of response time note 5) contrast ratio and response measurement system based on fig.9-6. fig.9-6. contrast ratio and response time measurement system drive signal of lcd panel non-select status select status non-select status relative brightness black t on t off 90% 10% on response time off response time drive and measurement system y + y ? x + z + z ? x ? brightness meter or luminance colorimeter (with luminosity correction function) black white
? 2 FLC43XWC8V-02 3 11 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation note 6) definition of optimum viewing angle based on fig.9-7. fig.9-7. definition of viewing angle note 7) definition of brightness uniformity brightness uniformity is defined by the following formula. brightness (i1~i9) art measured at the following 9 points ( 1 ~ 9 ) on the display area shown in fig.9-8. |min. in| brightness uniformity ( ? l) = 100 (%), n=1 to 9 |max. in| 192 640 1088 1 4 7 115 2 5 8 384 3 6 9 653 note) each measurement point ( 1 ~ 9 ) defines the center spot of brightness meter view. the tolerance of measurement position is 3mm. fig.9-8. measurement points 10 (-) (+) 0 6 o?clock viewing angle 12 o?clock max contrast ratio
? 2 FLC43XWC8V-02 3 12 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10. interface specifications 10. interface specifications 10. interface specifications 10. interface specifications 10-1-1. signal descriptions table 10-1 shows the description and configuration of interface signals (cn1). table 10-1-1. interface signals (cn1) pin symbol i/o function 1 v dd +5v power su p l y 2 v dd +5v power su p l y 3 gnd ground 4 gnd ground 5 rx0- lvds receiver si g nal ( - ) 6 rx0+ lvds receiver si g nal ( + ) 7 gnd ground 8 rx1- lvds receiver si g nal ( - ) 9 rx1+ lvds receiver si g nal ( + ) 10 gnd ground 11 rx2- lvds receiver si g nal ( - ) 12 rx2+ lvds receiver si g nal ( + ) 13 gnd ground 14 rxcl k - lvds receiver clock si g nal ( - ) 15 rxclk+ lvds receiver clock si g nal ( + ) 16 gnd ground 17 rx3- lvds receiver si g nal ( - ) 18 rx3+ lvds receiver si g nal ( + ) 19 gnd ground 20 data mapping select input i low : table 10-1-2 open or hi : table 10-1-3 upper side interface connector lcd module rear side 20 lower side connector d14h-20p-1.25h(hirose) user?s connector df14-20s-1.25 (hirose) 1 02 20020807 total revision
? 2 FLC43XWC8V-02 3 13 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10-1-2. lvds data mapping 1 table 10-1-2 shows the lvds data mapping 1.(datamappingselectinput = low) ? table 10-1-2. lvds data mapping 1 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? pin input system side pin lcd module pin output 51 txin0 27 rxout0 52 txin1 29 rxout1 54 txin2 30 rxout2 55 txin3 32 rxout3 56 txin4 33 rxout4 2txin5 txout3- txout3+ 17 18 rx3- rx3+ 34 rxout5 3txin6 35 rxout6 4txin7 37 rxout7 6txin8 38 rxout8 7txin9 39 rxout9 8txin10 41 rxout10 10 txin11 42 rxout11 11 txin12 43 rxout12 12 txin13 45 rxout13 14 txin14 46 rxout14 15 txin15 ? 47 rxout15 ? 16 txin16 ? 49 rxout16 ? 18 txin17 ? 50 rxout17 ? 19 txin18 ? txout1- txout1+ 8 9 rx1- rx1+ 51 rxout18 ? 20 txin19 ? 53 rxout19 ? 22 txin20 ? 54 rxout20 ? 23 txin21 ? 55 rxout21 ? 24 txin22 ? 1rxout22 ? 25 txin23 reserved txout3- txout3+ 17 18 rx3- rx3+ 2 rxout23 not use 27 txin24 reserved 3 rxout24 not use 28 txin25 reserved 5 rxout25 not use 30 txin26 enab 6 rxout26 50 txin27 txout3- txout3+ 17 18 rx3- rx3+ 7rxout27 txout0- txout0+ txout0- txout0+ 31 txclkin txout2- txout2+ txout2- txout2+ txclkout- txclkout+ symbol dclk transmitter ( ds90cf385) lcd control input interface connector receiver ( ds90cf386) txout1- txout1+ txout3- txout3+ txout1- txout1+ txout3- txout3+ 17 18 11 12 11 12 5 6 5 6 8 9 17 18 14 15 rx0- rx0+ rx0- rx0+ rx1- rx1+ rx3- rx3+ rx1- rx1+ rx3- rx3+ rx2- rx2+ rx2- rx2+ 8 9 rxclkout rxclk- rxclk+ 26 02 20020807 total revision
? 2 FLC43XWC8V-02 3 14 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10-1-3. lvds data mapping 2 table 10-1-3 shows the lvds data mapping 2.(datamappingselectinput = open or hi) ? table 10-1-3. lvds data mapping 2 ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? pin input system side pin lcd module pin output 51 txin0 27 rxout0 52 txin1 29 rxout1 54 txin2 30 rxout2 55 txin3 32 rxout3 56 txin4 33 rxout4 2txin5 txout3- txout3+ 17 18 rx3- rx3+ 34 rxout5 3txin6 35 rxout6 4txin7 37 rxout7 6txin8 38 rxout8 7txin9 39 rxout9 8txin10 41 rxout10 10 txin11 42 rxout11 11 txin12 43 rxout12 12 txin13 45 rxout13 14 txin14 46 rxout14 15 txin15 ? 47 rxout15 ? 16 txin16 ? 49 rxout16 ? 18 txin17 ? 50 rxout17 ? 19 txin18 ? txout1- txout1+ 8 9 rx1- rx1+ 51 rxout18 ? 20 txin19 ? 53 rxout19 ? 22 txin20 ? 54 rxout20 ? 23 txin21 ? 55 rxout21 ? 24 txin22 ? 1rxout22 ? 25 txin23 reserved txout3- txout3+ 17 18 rx3- rx3+ 2 rxout23 not use 27 txin24 reserved 3 rxout24 not use 28 txin25 reserved 5 rxout25 not use 30 txin26 enab 6 rxout26 50 txin27 txout3- txout3+ 17 18 rx3- rx3+ 7rxout27 txout0- txout0+ txout0- txout0+ 31 txclkin txout2- txout2+ txout2- txout2+ txclkout- txclkout+ symbol dclk transmitter ( ds90cf385) lcd control input interface connector receiver ( ds90cf386) txout1- txout1+ txout3- txout3+ txout1- txout1+ txout3- txout3+ 17 18 11 12 11 12 5 6 5 6 8 9 17 18 14 15 rx0- rx0+ rx0- rx0+ rx1- rx1+ rx3- rx3+ rx1- rx1+ rx3- rx3+ rx2- rx2+ rx2- rx2+ 8 9 rxclkout rxclk- rxclk+ 26 02 20020807 add this page
? 2 FLC43XWC8V-02 3 15 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10-2. color data assignment table 10-2 shows the color data assignment. table 10-2. color data assignment
6369?(5+? input data low level | high level brightness t??y?????????????? ? t??y?????????????? ? t?? y?? ?? ??? ?? ?? ??? ? basic color black blue green cyan red magenta yellow white ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? red black darker brighter red 0 1 2 253 254 255 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 1 : : : 0 1 1 0 1 0 : : : 1 0 1 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 green black darker brighter green 0 1 2 253 254 255 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 1 : : : 0 1 1 0 1 0 : : : 1 0 1 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 blue black darker brighter blue 0 1 2 253 254 255 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 0 0 0 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 0 : : : 1 1 1 0 0 1 : : : 0 1 1 0 1 0 : : : 1 0 1 note.1) definition of gray scale : color (n) ---?n? indicates gray scale level. the gray scale is brighter as the number is larger. note.2) data; 1: high, 0: low note.3) by inputting 8-bit data signal for each red, green and blue, this module can display 256 gray scale independently for each color. therefore, the module is able to display 16 million colors. color data are 24 lines.
? 2 FLC43XWC8V-02 3 16 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10-3. input signal timing table 10-3 and fig.10-3 shows the input signal timing. table 10-3. timing characteristics (t=0~50o c , vcc=50.25v) item symbol min. typ. max. unit remark dclk signal period tc 12.500 15.382 20.000 ns (clock) frequency fc 50.00 65.01 80.00 mhz fc=1/tc duty tch/tc 45 50 55 *1 high time tclkh 5.0 ? ? ns low time tclkl 5.0 ? ? ns rise time tclkr ? ? 5.0 ns fall time tclkf ? ? 5.0 ns dclk-data setup time tset (4.5 ) 4 ? ? ns timing hold time thold (6.5) 4 ? ? ns horizontal period th 1340 1344 (3012) 1688 dclk frequency fh 46.6 48.3 55.5 khz display period thd 1280 1280 1280 dclk *2,3 ve rti cal period tv 776 806 806 th 16.67ms frequency 1/tv (50) 60 (75) hz wxga mode display period tvd 768 768 768 th *2,3 data-enab timing data-enab timing tdn 0 0 0 dclk *4 *1) dclk signal input must be valid while power supply is applied. *2) display position is specified by the enab signal only. ? horizontal display position is specified by the rise of enab signal. the data which is latched by the falling edge of 1st dclk right after the rise of enab, is displayed on the left edge of the screen. ? vertical display position is specified by the rise of enab after a ?low? level period equivalent to eight times of horizontal period. the 1st data corresponding to one horizontal line after the rise of enab is displayed at the top line of screen. *3) if a period of enab ?high? is less than 1280 dclk or less than 768 lines, the rest of the screen displays black. *4) the display position does not fit to the screen if a period of enab ?high? and the effective data period do not synchronize with each other. 02 20020807 correct values of dclk frequency 04 20021205 change parts in table10-3
? 2 FLC43XWC8V-02 3 17 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation dclk r0-7 g0-7 b0-7 r0-7 g0-7 b0-7 enab r0-7 g0-7 b0-7 enab dclk r0-7 g0-7 b0-7 enab fig.10-3.input signal timing chart tch tc tc 1 tset thold ??y ? ? ? ? ? tclkh tclkl tclkr tclkf ? ? ? ? th thd ?t? ? 000 1 0002 0003 ? ? ? y ? ?t? ? ?t ? ?ty ? ?tt ? ?t ? ?? ? tdn=0clk tdn=0clk tc
? ?
ty? ? tvd tv
? 2 FLC43XWC8V-02 3 18 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 10-4. correspondence between data and display position fig.10-4 shows the correspondence between data and display position . ? ? r 0001 g 0001 b 0001 r 0002 g 0002 b 0002 r 0003 g 0003 g 1280 b 1280 r 0001 g 0001 b 0001 r 0002 g 0002 b 0002 r 0003 g 0003 g 1280 b 1280 fig.10-4.correspondence data and display position 10-5. power supply sequence the sequence of input signals and on/off of the power supply of this lcd module should be in the specification shown in fig.10-5 to prevent latch-up of the driver ics and dc driving of the lcd panel. fig.10-5. power supply sequence s0001 s0002 s0003 s0004 s0005 s0006 s0007 s0008 s3839 s3840 c001 c768 n? t4 Q Q t5 Q 40ms t2 ? 4.75v 4.75v (4.5v) ? t1 Q 20ms 4.75v 90% 10% 4.75v 0.5v 0.1s Q t7 n? n? n? on off (0v) ? h l dclk should be in a range of the spec.(frequency etc. of the lcd. 0ms Q t2 Q 40ms inputs should be in a range of the spec. of the lvds. tri-state tri-state t6 Q 20ms v cc lv d s differential input
? 2 FLC43XWC8V-02 3 19 edit date appr. check desig. description cust. ecexeueued / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 11. backlight specifications 11. backlight specifications 11. backlight specifications 11. backlight specifications ? ? ? ? 11-1. pin configuration for backlight table 11-1(a) and 11-1(b) shows the description and pin assignment of the connectors (cn-a and b) for the backlight of this lcd module. table 11-1(a) pin assignment of cn-a table11-1(b) pin assignment of cn-b ? ? ? ? pin o signal function cable color pin o signal function cable color 1 v l 1 power supply for ccfl 1 red 1 v l 3 power supply for ccfl 3 red 2 v l 2 power supply for ccfl 2 red 2 v l 4 power supply for ccfl 4 red 3 nc ?? 3 nc ?? 4 gnd ground (for v l 1, 2) white 4 gnd ground (for v l 3, 4) white ? connector : housing : bhr-04vs-1 : contact : sbh-001t-p0.5 user?s connector : post with base : sm04(4.0)b-bhs-1-tb supplier : japan solderless terminal trading company ltd. (j.s.t.) ? ? 11-2. ccfl supplier : sanken electric co., ltd part no. sd26e3850e8350b3113000 11-3. life the life of the backlight is a minimum of 25,000 hours at the following conditions. (1) working conditions ? ambient temperature : 25 5o c ? tube current(i l ) : (10.5ma or less) (2) definition of life ? brightness becomes 50% or below 50% of the minimum brightness value shown in table 9-1. ? the lamp cannot be lit by the breakdown voltage of 1600vvms. ? lamp is flashing. 11-4. lamp assembly set (for replacement) lamp assembly set (with charge) is prepared for maintenance. this set consists of an upper lamp assembly and a lower lamp assembly. type number : flcl-21
? 2 FLC43XWC8V-02 3 20 edit date appr. check desig. description cust. nlnan^n^nm / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 12. appearance specifications 12. appearance specifications 12. appearance specifications 12. appearance specifications 12-1. zone ? inside display dot area (369.6 221.8mm) ? display dot area means active area. ? one pixel consists of 3 dots (red, green and blue). ? foreign particle and scratch unharmful to display image, such as the foreign particle under polarizer film but outside of the display area and scratch on metal bezel, backlight module or polarizer film out of the display area, etc., are not counted. 12-2. bright spots (1) bright spots by the defect of tft. visible under bias of 2% nd filter ................................ high bright spot rg visible under 5% but invisible under 2% nd filter ..... low bright spot rgb invisible under bias of 5% nd filter ............................. not counted (2) bright spots by the light passing through tears, breaks, etc in color filter. exceed size of a half dot ................................................. high bright spot a half dot or less ............................................................. not counted (3) bright spots by the light passing through tears, breaks, etc in chromium mask. exceed 50 m ................................................................... high bright spot 50 m or less ................................................................... not counted 12-3. test condition ? inspector must observe the lcd screen from the normal direction under the illumination by a single 20w fluorescent lamp. the distance between the lcd screen and the inspector should be a height of 50cm above the worktable. the vertical illuminance is 300 to 600lux (reference value). ? bright spot should be counted under entire black screen. ? dark spot should be counted under entire white screen. ? frame frequency should be 60hz. 12-4. specifications table 12-4 shows the appearance standard. (note1) please do not mistake a single bright spot for a bright spot connection due to cs(supplemental capacitance) line at the center of each dot. (note2) if a pixel is dark partially, it connects into the number of dark spots in accordance with following rule. (a) s<1/3 : not count. only one of 4 dark connection is allowed. (b) 1/3< s<2/3 : considered as 0.5 dot. (c) 2/3< s : considered as 1 dot. (s=dark spot size/dot size) ? (note3) min. distance between foreign particles : 100mm 03 20020924 add (note3)
? 2 FLC43XWC8V-02 3 21 edit date appr. check desig. description cust. nlnan^n^nm / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation no. item ? jud g ment method and standard ? 1 bright spot (high and low) < 3 dots (note 1) 2 bright spot connection (high and low) < 1 pair (note 1) (2 dot connection in horizontal) 3 total of bright spot < 3 dots 4 dark spot < 5 dots (note 2) 5 dark spot connection < 2 pairs (2 dot connection in horizontal) (note 2) 6 total of dark spot < 5dots (note 2) 7 total of dot defect(bright and dark) < 8 dots 8 high-high high > 15mm distance of bright spot others > 5mm 9 distance of dark spot > 5mm w Q 0.03 DDDD not count l Q 6 not count 6 l Q 12 Q 5 0.03 w Q 0.05 12 l 0 l Q 0.6 not count 0.6 l Q 5 Q 3 0.05 w Q 0.10 5 l 0 w l Q 0.4 Q 1 0.15 w Q 0.3 0.4 w l 0 ? ? ? ? ? ? ? ? ? ? ? ? scratch on polarizer ? ? ? ? ? ? ? ? ? ? 0.10 w DDDD 0 d Q 0.3 not count 0.3 d Q 0.4 Q 6 ?? ? ? ? dent on polarizer ? ? 0.4 d 0 d Q 0.3 not count d Q 0.5 not count ? ? ? ? bubble in polarizer ? ? ? 0.5 d 0 d 0.5 Q 5 ? ? ? spot (black/white) by foreign particle ? 0.5 Q d 0 d Q 0.2 not count 0.2 d Q 0.3 Q 2 0.3 d Q 0.35 1 ?? ? ? ? ? bright spot by fiber foreign particle (under the polarizer. i.e. between the polarizer and the glass) (note 3 ) ? 0.35 d 0 w Q 0.03 DDDD not count l Q 6 not count 6 l Q 12 Q 5 0.03 w Q 0.05 12 l 0 l Q 0.6 not count 0.6 l Q 5 Q 3 0.05 w Q 0.1 5 l 0 ? ? ? ? ? ? ? ? ? ? line (black /white), scratch by fiber foreign particle 0.1 w (w+l)/2 d count as spot (black/white) of no.13 d:average diameter [mm], w:width [mm], l:length [mm], s=(bright spot size)/(dot size) 03 20020924 total revision 04 20021205 total revision
? 2 FLC43XWC8V-02 3 22 edit date appr. check desig. description cust. nlnan^n^nm / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation applied area item condi tion specification as for the display position in the display dot area, the variation of tolerance between window frame of the upper bezel and dot display area (right, left, up and down) is shown in the following table. tolerance (x direction) tolerance (y direction) |e-f| Q 1.0mm |a-b| Q 1.0mm |e-h| Q 0.7mm |a-d| Q 0.7mm |f-g| Q 0.7mm |b-c| Q 0.7mm |g-h| Q 1.0mm |c-d| Q 1.0mm display dot area display location non- lighting *the dimension of effective display area, dot display area and display frame should follow the dimensions described in each specification. 04 20021205 add this page dot display width dot display width opening dimension of bezel effective dis p la y area dot display area width of display frame width of display frame bezel y x b a e f d c g h opening dimension of bezel
? 2 FLC43XWC8V-02 3 23 edit date appr. check desig. description cust. nlnan^n^nm / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 13. environmental specifications 13. environmental specifications 13. environmental specifications 13. environmental specifications table 13-1 shows the environmental specifications. table 13-1. environmental specifications item condition remark operation 0~57o c (note1) temperature storage -20~60o c temperature on surface of lcd panel (display area.) operation 20~85%rh humidity storage 5~85%rh maximum wet-bulb temperature should not exceed 29o c . no condensation. vibration non-operation 10~500hz, 1 cycle/20minute, 2g, 1.5mm max, 2hour each x, y and z directions shock non-operation 30g, 6ms, 1time each x, y and z directions. for single module without package.(note2) note1: temperature on surface of lcd panel should be under 57 ? . note2: table 13-2 and fig. 13-1 show the shock resistance standard when module is packaged. table 13-2. shock resistance standard when module is packaged dropping location dropping height count a ~ j 60cm 1 time fig.13-1. direction to apply shock to package f ( side face ) g (top face) ? (rear face) e ( side face ) c (edge) i (front face) b (edge) d (edge) h (bottom face) a (corner)
? 2 FLC43XWC8V-02 3 24 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 14. indications 14. indications 14. indications 14. indications this module has the following indications. ? (1) product name : lcd unit (2) model number : FLC43XWC8V-02 (3) product drawing number : na19026-c071 (4) manufacturing number : 2 y 0 0 0 0 1 (5) version number : 01a (example) -1st 2 digits ?01? means operational version. -3rd alphabet means functional version. (6) country of origin : made in japan (7) company name : fujitsu display technologies corp. (8) caution when changing cold-cathode tubes and disposal method of them. (see fig. 14-1) 15. packaging 15. packaging 15. packaging 15. packaging separately specified in packaging specifications. 15-1. packaging specifications (1) 5 lcd modules / 1 package. (2) weight: approximately 13kg / 1 package. (3) outline dimensions : 348mm(w) 328(d) 490mm(h) 15-2. packaging method fig.15-2 (a),(b),(c),(d) show the packing method. serial number (to be reset every month on 1st.) manufacturing month (oct. = x, nov. =y, dec. =z) last digit of manufacturing year. ? when changing cold cathode fluorescent lamps, follow operating specifications. especially be careful about the lamp ? s side-edge. ? w?QI?????w?????? ? this tft color lcd contains cold cathode fluorescent lamps. please follow local ordinances or regulations for its disposal. ? ?????????w?Mz???? ???t??? fig.14-1 lcd unit lcd unit lcd unit lcd unit made in japan FLC43XWC8V-02 0x50015 na19026-c071 01a fujitsu display technologies corp. fig.14-2 product label (example)
? 2 FLC43XWC8V-02 3 25 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation fig.15-2(a) packaging method protective sheet front side rear side front side anti-electric bag tape
? 2 FLC43XWC8V-02 3 26 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation fig.15-2(b) packaging method holder(bottom) lcd unit holder(upper) label(example) (type) FLC43XWC8V-02 (qty.) 5 na19026-c071 01 a (drwg. no.) (rev. no.) 9x00001 9x00002 9x00003 9x00004 9x00005 `` made in japan taping upper : h or i method bottom : h method upper and bottom holders should be anti-electrostatic t yp e. (328) (490) (348)
? 2 FLC43XWC8V-02 3 27 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation fig.15-2(c) packaging method upper board wrap film corrugated carton pp belt carton angle t.b.d. t.b.d t.b.d.
? 2 FLC43XWC8V-02 3 28 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation note 1) the carton (a) should be placed in the middle of the container(b) with enough cushioning materials. figure.15-2(d) packaging method 446 (430) 646 (630) cushioning material corrugated carton(a) with lcd modules corrugated fiberboard shipping container(b) 602 (580)
? 2 FLC43XWC8V-02 3 29 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 16.warranty 16.warranty 16.warranty 16.warranty the warranty period is one year after manufacturing. products which fail during this period are repaired or replaced without charge, unless the failure is caused by user. 17.precautions 17.precautions 17.precautions 17.precautions adhere to the following precautions to properly use this lcd module. (1) fail safe design (1) fail safe design (1) fail safe design (1) fail safe design lcd module has an inherent chance of failure. customers must protect against injury, damage or loss from such failures by incorporating safety design measures into your facility and equipment such as redundancy, fire protection, and prevention of over-current levels and other abnormal operating conditions. (2) han (2) han (2) han (2) handling of lcd panel dling of lcd panel dling of lcd panel dling of lcd panel ? ? ? ? do not apply any strong mechanical shock to the lcd panel. do not apply any strong mechanical shock to the lcd panel. do not apply any strong mechanical shock to the lcd panel. do not apply any strong mechanical shock to the lcd panel. since the lcd panel is made of glass, excessive shock may damage the panel or cause a malfunction. ? ? ? ? do not press hard on the lcd panel surface. do not press hard on the lcd panel surface. do not press hard on the lcd panel surface. do not press hard on the lcd panel surface. in the lcd panel, the gap between two glass plates is kept precisely and uniformly to maintain display?s characteristics and reliability. if this panel is pressed hard, the following troubles occurs. (a) ununiformity of color (b) orientation of liquid crystal becomes disordered problem (a) returns to normal after a while. problem (b) returns to normal if power is shut off once then turned on again. however these operations should be avoided to insure reliability. ? ? ? ? do not scratch the polarizer film on the lcd panel surface. do not scratch the polarizer film on the lcd panel surface. do not scratch the polarizer film on the lcd panel surface. do not scratch the polarizer film on the lcd panel surface. do not press or rub the display surface with a hard tool, pincet, etc. for handling, use cotton or conductive gloves so that the display surface is not stained. for if the display surface is stained by dust or dirt, clean it as follows with a soft cloth ? (deer skin, etc.) [dust] wipe off with a soft cloth. (do not rub.) [dirt ] wipe off lightly with a soft cloth after soaking in the clear water and squeezing hard out of water drops. only if the dirt is hardly wiped off, use isopropyl alcohol or ethanol. be careful not to splash the water or the solvent and water penetrated between the polarizer and the lcd panel. do not use solvents such as ketone (acetone, etc.) and aromatics (xylene, toluene, etc.) if saliva or water drops are left for long time, it may deform partial deformation or discolored. ? wipe off immediately in the same way as for dirt. do not allow oil to adhere to the module, since the cleaning of oil is difficult. ? ? ? ?? ? ? ? do not place or contact objects on the display surface for a long period of time. do not place or contact objects on the display surface for a long period of time. do not place or contact objects on the display surface for a long period of time. do not place or contact objects on the display surface for a long period of time. that?s because this may make some parts of the lcd module distorted and the display quality may decline.
? 2 FLC43XWC8V-02 3 30 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation (3) handling of lcd module (3) handling of lcd module (3) handling of lcd module (3) handling of lcd module ? ? ? ? do not pull the cold do not pull the cold do not pull the cold do not pull the cold- - - -cathode tube cable strongly. cathode tube cable strongly. cathode tube cable strongly. cathode tube cable strongly. if the cable is pulled with the loaf of 2kg or more, the cable may be damaged or reliability may decrease. ? ? ? ? assemble the module into user?s system in a dust free environment. assemble the module into user?s system in a dust free environment. assemble the module into user?s system in a dust free environment. assemble the module into user?s system in a dust free environment. if conductive foreign matter adheres to the module, failures may occur. ? ? ? ? take anti take anti take anti take anti- - - -static measures for assembling the module. static measures for assembling the module. static measures for assembling the module. static measures for assembling the module. since the lcd module contains cmos-ics, the following considerations are necessary. for assembling the module, operator should be grounded and wear cotton or conductive ? gloves. floor of work area and work table to assemble the lcd module should be covered with electrostatic shielding in order to discharge static electricity via an earth wire. if necessary, ground operation tools (soldering iron, radio pliers, pincet, etc.). do not take the module out of the conductive bag until the time when the module is assembled. assemble the module under low humidity (50%rh or less). ? ? ? ? do not pull the connecting cable on the rear face of the lcd module strongly. do not pull the connecting cable on the rear face of the lcd module strongly. do not pull the connecting cable on the rear face of the lcd module strongly. do not pull the connecting cable on the rear face of the lcd module strongly. ? ? ? ? do not disassemble or remodel the lcd module. do not disassemble or remodel the lcd module. do not disassemble or remodel the lcd module. do not disassemble or remodel the lcd module. if this lcd module is disassembled or remodeled, it may have some trouble, or the display quality and reliability may not be assured. (4) precautions for operating the lcd module (4) precautions for operating the lcd module (4) precautions for operating the lcd module (4) precautions for operating the lcd module ? ? ? ?? ? ? ? adhere to the specified power supply sequence. adhere to the specified power supply sequence. adhere to the specified power supply sequence. adhere to the specified power supply sequence. if not followed, the cmos-ic may cause a latch-up, or the dc voltage may be applied the liquid crystal, and a failure or serious deterioration in display quality may occur. ? ? ? ?? ? ? ? do not operate the lcd module when condensation is present. do not operate the lcd module when condensation is present. do not operate the lcd module when condensation is present. do not operate the lcd module when condensation is present. if the lcd module is operated when condensation is on the terminals of the lcd panel, the terminals cause electrochemical reaction, and may reach disconnection. condensation easily occurs especially when the module is moved from a cold environment to a warm environment. ? ? ? ?? ? ? ? trouble that occurs when the lcd module is used at not recommended temperature. trouble that occurs when the lcd module is used at not recommended temperature. trouble that occurs when the lcd module is used at not recommended temperature. trouble that occurs when the lcd module is used at not recommended temperature. operation at high temperature(>60oc) :display colors shift to blue. storage at high temperature (>60oc) :the polarizer film deteriorates and contras decreases. operation at low temperature (<0oc) :the response speed decreases considerably. storage at low temperature (<-20oc) :the liquid crystal may solidify and become damaged. ? ? ? ?? ? ? ? always input the control signals at the correct timing. always input the control signals at the correct timing. always input the control signals at the correct timing. always input the control signals at the correct timing. if control signals (dclk, or enab) are not input, or if the timing is out of the specified timing, dc voltage may be applied to the liquid crystal and, as a result, cause image sticking or deterioration of contrast.
? 2 FLC43XWC8V-02 3 31 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation (5) precautions on designing module mounting (5) precautions on designing module mounting (5) precautions on designing module mounting (5) precautions on designing module mounting ? ? ? ? do not press the display surface and bottom face of the lcd module. do not press the display surface and bottom face of the lcd module. do not press the display surface and bottom face of the lcd module. do not press the display surface and bottom face of the lcd module. display quality or reliability may be deteriorated if the installation of the lcd module is inappropriate and, as a result, excessive pressure is applied to the surface of lcd screen. brightness uniformity or the reliability of ccfl may decrease if the pressure is applied to the backlight module. ? ? ? ? consider the module mounti consider the module mounti consider the module mounti consider the module mounting design, so that twisting and bending do not occur to the ng design, so that twisting and bending do not occur to the ng design, so that twisting and bending do not occur to the ng design, so that twisting and bending do not occur to the ? ? ? ? lcd module. lcd module. lcd module. lcd module. excessive twisting and bending may damage display quality and reliability. ? ? ? ? the power cable length between the lcd module and inverter should not be extended. the power cable length between the lcd module and inverter should not be extended. the power cable length between the lcd module and inverter should not be extended. the power cable length between the lcd module and inverter should not be extended. otherwise the backlight may not light or flickering may occur. ? ? ? ? do not make the powe do not make the powe do not make the powe do not make the power cable of the backlight clung to a metal plate, etc. r cable of the backlight clung to a metal plate, etc. r cable of the backlight clung to a metal plate, etc. r cable of the backlight clung to a metal plate, etc. backlight frequency current for backlight driving may leak to the metal and desired brightness may not be assured. ? ? ? ? when mounting lcd module with m4 screw(x4) should be screw up under 5.75kgfcm torque. when mounting lcd module with m4 screw(x4) should be screw up under 5.75kgfcm torque. when mounting lcd module with m4 screw(x4) should be screw up under 5.75kgfcm torque. when mounting lcd module with m4 screw(x4) should be screw up under 5.75kgfcm torque. (6) storage method (6) storage method (6) storage method (6) storage method ? ? ? ? do not store the lcd module in an atmosphere of organic solvent or corrosive gas. do not store the lcd module in an atmosphere of organic solvent or corrosive gas. do not store the lcd module in an atmosphere of organic solvent or corrosive gas. do not store the lcd module in an atmosphere of organic solvent or corrosive gas. in an organic solvent atmosphere, the polarizer film discolors and display quality deteriorates. in a corrosive gas environment, various problems may occur. ? ? ? ? store the lcd module in a fujitsu package. store the lcd module in a fujitsu package. store the lcd module in a fujitsu package. store the lcd module in a fujitsu package. at storing, fujitsu packages can be stacked up to 4 boxes. the lcd module is in an anti-static bag. keep the module in that status. ? ? ? ? it is recommended that the storage environment should be humidity controll it is recommended that the storage environment should be humidity controll it is recommended that the storage environment should be humidity controll it is recommended that the storage environment should be humidity controlled, cool and ed, cool and ed, cool and ed, cool and ? ? ? ? dark. dark. dark. dark. recommended storage environment place ???? :dark (avoid direct sunlight) temperature : 10~35oc humidity : 50~60%rh note) if the module is left in an environment of 60 ? or more for a long period of time, optical characteristics may deteriorate. (7) storage method (7) storage method (7) storage method (7) storage method ? ? ? ?? ? ? ? if the lcd panel is damaged, do not inhale or allow the liquid crystal to enter the mouth if the lcd panel is damaged, do not inhale or allow the liquid crystal to enter the mouth if the lcd panel is damaged, do not inhale or allow the liquid crystal to enter the mouth if the lcd panel is damaged, do not inhale or allow the liquid crystal to enter the mouth if the liquid crystal contacts the body or cloths, wash it off with soap immediately. follow precautions for regular electronic components. ? ? ? ?? ? ? ? sol sol sol solder flux on the printed circuit board is harmless to the quality and reliability of lcd der flux on the printed circuit board is harmless to the quality and reliability of lcd der flux on the printed circuit board is harmless to the quality and reliability of lcd der flux on the printed circuit board is harmless to the quality and reliability of lcd ?? ?? ?? ?? module. module. module. module. fujitsu is practicing non-wash technology on module assembly process.
? 2 FLC43XWC8V-02 3 32 edit date appr. check desig. description cust. / date document control section 1 d d e f b a desig. check appr. FLC43XWC8V-02 tech bes lcd-00149 1 2 3 4 a b c c fujitsu display technologies corporation 18. precautions for use 18. precautions for use 18. precautions for use 18. precautions for use this product is designed, developed and manufactured as contemplated for general use, including without limitation, general office use, personal use, household use, and ordinary industrial use, but is not designed, developed and manufactured as contemplated for use accompanying fatal risks or dangers that, unless extremely high safety is secured, could lead directly to death, personal injury, severe physical damage or other loss (hereinafter ?high safety required use?), including without limitation, nuclear reaction control in nuclear facility, aircraft flight control, air traffic control, mass transport control, medical life support system, missile launch control in weapon system. if customer?s product possibly falls under the category of high safety required use, please consult with our sales representatives in charge before such use. in addition, fdtc shall not be liable against the customer and/or any third party for any claims or damages arising in connection with the high safety required use of the product without permission. 19. miscellaneous 19. miscellaneous 19. miscellaneous 19. miscellaneous specifications of the tft-lcd panel and other components used in the lcd module are subject to change. both parties shall discuss together before change. if any doubt is raised in the content of the specifications, both parties shall discuss and make best effort for the agreement.

▲Up To Search▲

Price & Availability of FLC43XWC8V-02

	To Download FLC43XWC8V-02 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .